China

Shenzhen City

info@bfymold.com

Office Hour 09:00am - 06:00pm

ISO 9001:2015

Certified Company

Manufacturing Insights

Tooling, materials and injection molding guides

Overmolding Material Compatibility: TPU and TPE with ABS, PC and PP

Overmolding material compatibility starts with a pair of resin grades, a part geometry, and a service condition. “TPU on ABS” describes the materials broadly, but it does not tell you whether the selected grades will bond, whether the edge will lift, or whether the assembly will still work after use. Use this guide to turn a candidate TPU or TPE pairing with ABS, PC, or PP into a testable design decision.

Screen the Exact Material Pair

Record the supplier and grade for both shots, along with colorant, reinforcement, and additives that may affect the interface. Ask the soft-material supplier whether it recommends that grade for the specific substrate and process. Check how representative its test data are of your geometry and service conditions. Avient’s TPE selection guide lists different formulated grades for different substrates. Those recommendations apply to the products and conditions described by the supplier.

Material Screening Questions Before Overmold Trials
Rigid substrateWhat to specifyWhat to verify
ABSExact ABS grade, texture, color and visible boundaries.Check supplier guidance for ABS, then inspect adhesion at the actual edge and appearance zones after molding.
PC or PC/ABSIdentify the exact polymer or blend and any clear, coated or stressed region.Check that the second shot and conditioning leave the part functional and visually acceptable. Treat PC and PC/ABS as separate candidates.
PPExact PP grade, filler or surface condition, and the proposed TPU or TPE grade.Seek grade-specific supplier evidence for PP. If the interface needs mechanical retention, validate it in the load direction in service.

These are screening questions. A grade listed for one substrate is not automatically a candidate for another. Where the soft layer is TPU, check the supplier’s drying and processing instructions for that grade. The TPU injection molding guide explains how material preparation fits into the process.

Design for Adhesion, Mechanical Retention and Appearance

With adhesion, load crosses the material interface. With mechanical retention, features such as through-holes or undercuts restrain the soft material by geometry. Some designs use both. Review whether the tool can fill and release those features, whether the substrate remains strong enough, and whether a lifted edge would still cause a functional or cosmetic failure. A captured layer does not establish that an interface seals.

For an illustrative handheld enclosure, identify where the grip will see repeated peeling or twisting and where the user will see the boundary. Keep the soft layer clear of mating faces or clips unless it is part of their function. Mark flash limits, the allowed witness line, and any required grip or assembly checks on the drawing. This example describes a design review, not a customer project or a tested pairing.

Turn the Material Choice Into a Validation Plan

  1. Screen the gradesConfirm the substrate and soft-grade IDs and request supplier data for the proposed pair.
  2. Define the interfaceMark the loads, retention features, appearance limits and assembly clearances.
  3. Check representative samplesRecord the production route, sample geometry and conditioning. Choose separation or functional checks that reflect use.
  4. Record the release conditionsAgree the acceptable load or failure mode for the application and what changes require another check.

A flat coupon can help screen the bond. It does not reproduce a thin edge, an interlock or a curved grip. If peel is relevant, agree the specimen geometry, pull direction or angle, speed, conditioning and reporting method. Record whether the interface separates, the soft layer tears, the substrate fails or the interlock pulls free. When the component must seal, survive cleaning or fit a mating part, add an appropriate component-level check.

For repeat orders, retain grade IDs, drawing revision, sample identification, trial conditions and the approved record. If the resin grade, color system, surface preparation or molding route changes, assess which evidence still applies. Avient’s overmolding guide explains how part design, processing and adhesion interact.

Overmolding Compatibility FAQs

Will TPU bond to every ABS or PC grade?

No. Check supplier guidance for the exact pair and confirm retention under representative processing, geometry and service conditions.

Can a mechanical lock help on a PP substrate?

It is one design option. Confirm that the features can be molded and that the assembled part resists the expected loads and meets appearance requirements. If the interface must seal, test sealing separately.

Can I compare peel values from different sources?

Compare the methods before comparing numbers. Part geometry, specimen width, angle, speed, conditioning and how the result is reported can affect the comparison.

Prepare an Overmolding Review Brief

Share the two candidate grades, the CAD interface, visible surfaces and the loads or exposure the assembly must handle. For a soft layer on a substrate, use the overmolding service page. For a preformed metal component placed in the mold, see insert molding services.

Discuss Material and Part Requirements →

Drag & Drop Files, Choose Files to Upload You can upload up to 5 files.
Attach up to 5 PDF, JPG, PNG or ZIP files (50 MB per file). Put CAD files such as STEP/STP, IGES or X_T in a ZIP archive. You can also email files to info@bfymold.com.
×

Table of Contents